52 Piece Clamp Kit-7/16”
Use this 52-piece clamp set to hold down practically any shaped workpiece to the milling table. Set includes: 24 studs, 4 each of 3”, 4”, 5”, 6”, 7” and 8”, Six pair of no-slip step blocks, 6 t-nuts, 6 flanged nuts, 4 coupling nuts and a holding case.
|
Fly Tool Cutter Kit
Cut flat surfaces in a path up to 4” wide with these counterbalanced cutters. Cutter heads are hardened steel with 1/2” shanks. Includes body sizes 1-1/16”, 1” and 1-3/8” plus tool bits. MT3 spindles (Midas Series) require adapter #65-015. R-8 spindles (Granite, Granite Industrial, CX and LX) require R-8 collet, item #66-260.
|
Edge and Center Finder, Fisher
Made in the USA by hungry machinists. This 3/8" diameter combination edge and center finder helps you locate work on your mill. The edge finder end has a 0.200" diameter cylinder to quickly find the edge of a work piece. The center finder end tapers to a point to locate holes. The edge and center finder is hardened and ground all over. The edge and center finder is furnished with a quality vinyl case. This is a quality American-made product from Fisher Machine Shop.
|
V-block set
Round stock sits firmly in the v-groove of these 1-1/4" square x 1-5/8" long blocks. Includes iron clamps with 1" capacity.
|
End Mill Set,4 Fluted HSS
This versatile set has all the most popular sizes including 1/8”, 3/16”, 1/4”, 5/16” and 3/8” sizes with 3/8” shanks and 1/2” with a 1/2” shank.
|
4" Superlock Vise With Swivel Base
Our best milling vise with precision machined surfaces holds your work securely. Comes complete with swivel vise and mounting hardware. Three-inch has jaws 3-3/16” wide and 1” deep with 3” opening. Four-inch has jaws 4” wide and 1-3/8” deep with a 4” opening.
|
Angle Block Set
Ten piece angle block set. The angles included are 1°, 2°, 3°, 4°, 5°, 10°, 15°, 20°, 25°, 30°. You can combine them to make any integral angle.
|
Slotted Angle Plate
When you need to set up at 90 degrees to the table, reach for this angle plate. Heavy and gusseted for rigidity, the plate is 6” long, 5” wide, and 4-1/2” high.
|
Slit Cutter, 4” x 1/16” with 1” Hole
Machine slots, keyways, and splines in large gears with this 4x1/16” HSS cutter. Ideal for general-purpose slotting and cut-off operations, this 36-tooth cutter fits saw arbor #65-055 for the machines with an R-8 Spindle. Use stub arbor, 65-075 with the machines with an MT3 spindle.
|
4 FL HSS Single Endmills
End Mill Single 4FLHSS
All the basics you need.
|
Wiggler Center Finder Set
For accurately locating working points on the drill press and the milling machine, you can't beat this set. Includes indicator holder, ball contact (0.250"), disc contact (0.100"), needle point shaft and wiggler body. Protected in vinyl case.
|
Face Mill Insert
This C6 Carbide inserts fits Smithy face mill cutters 68-010 and 68-080. Technical reference number SPG 422. Note: Pricing is for one insert.
|
Face Mill Replacement Screw (Fits 68-080)
Screw secures face mill insert in place. Two styles available. Tapered cap screw 68-017 fits 68-010 face mill cutter (68-010 face face mill cutter has an MT3 shank), setscrew 68-018 shown above fits 68-080 (R8 taper shank).
|
0-90° Angle Vise, 3-1/4” Jaw Opening
For quick setups horizontal, vertical, or somewhere in between, use this 0-90° graduated vise. Jaw width and opening is 3-1/4”, depth is 1-1/4”. This item is designed for drillpress operation and is only suitable for light milling work, will not acommodate standard parallels.
|
Dividing Plates for 6” Rotary Table
Add a dividing plate to your rotary table and super indexer to mill slots or drill holes at any equal increment. 2 Plates included.
|
Tailstock for 6” Rotary Table
Support your work with this tailstock when using your rotary table in the vertical position. Perfect to use when indexing a cylindrical workpiece.
|
Automatic Center Punch, Starrett
This punch has a lightweight, knurled aluminum handle for a positive grip and easy handling. No hammer is required! Just hold the punch in an upright position, press the handle down, and a built-in mechanism strikes a perfect center mark every time. The force of the blow can be adjusted by turning the knurled cap. All working parts are made of tool steel, properly hardened. The hardened tool steel point can easily be removed for resharpening or replacement. Works on metal, plastics, wood and other machinable materials. Weight: 0.20 pounds
|
Saw Arbor
Mount a side cutter or slitting saw in your R-8 millhead with this arbor. Precision ground and hardened, this arbor features a R-8 shank, four T-Spacers (1”,1/2”, and 2 1/4”) to adjust blade depth, and a locking nut with reverse threads to lock the cutter. 1" Diameter. For use with machines that have an R-8 mill spindle.
|
8” Precision Rotary Table
Rotary Table
Drill holes and bolt-hole patterns, mill intersecting slots and curved slots precisely. Includes worm drive hand wheel with Vernier ring for 4-degree table movement per turn, four T-slot ways, and two table clamp handles for stability. Main body mounts horizontally and vertically. 6” table is 3-1/4” high with MT2 bore and takes 7/16" T-Slots (35-105). The 8” table needs 1/2” T-slot nuts (35-110) and has a MT3 bore.
|
Dividing Plates for 8” Rotary Table
Add a dividing plate to your rotary table and super indexer to mill slots or drill holes at any equal increment. 2 Plates included.
|
Tailstock for 8” Rotary Table & Super Indexer
Support your work with this tailstock when using your rotary table in the vertical position. Perfect to use when indexing a cylindrical workpiece.
|
Double-Ended End Mill Set
Save money with this set of four-flute HSS end mills. This set of 3/8” shank end mills includes: 1/8”, 5/32”, 3/16”, 1/4”, 5/16”, and 3/8”
|
3/8” End Mill Adapter-R-8
R8 Mill Adapters
These end mill adapters are the most secure way to hold your end mill. Bored to accept the exact shaft size of the end mill and secured with a set screw, end mills won't move or flex during your milling operation.
|
End Mill Set, 4 Fluted TiN 10 PC Set
Plunge cut and take larger cuts with these center cutting Tin-coated, single end mills. These long-lasting sets contain sizes: 3/16”, 1/4”, 5/16”, 3/8”, and 7/16” with 3/8” shanks; 1/2” and 9/16” with 1/2” shanks; 5/8” and 11/16” with 5/8” shanks; and 3/4” with a 3/4” shank.
|
Parallels, 6 Piece Adjustable Set
You'll have the perfect size parallels for every job with this set. Six adjsutable pairs range from 3/8" to 2-1/4" wide, 1-3/4" to 5" long. Adjust to measurement with lock down and setscrew.
|
Ball Nose End Mill Kit, 2 Flutes HSS
Ball endmills are used when you want to cut a rounded groove. Great for die makers. This set includes 1/8”, 3/16”, 1/4”, 5/16”, and 3/8” sizes with 3/8” shanks;7/16”, 1/2”, and 5/8” with 1/2” shanks; and 3/4” with a 3/4” shank.
|
3" Superlock Vise With Swivel Base
Our best milling vise with precision machined surfaces holds your work securely. Comes complete with swivel vise and mounting hardware. Three-inch has jaws 3-3/16” wide and 1” deep with 3” opening. Four-inch has jaws 4” wide and 1-3/8” deep with a 4” opening.
|
Machinist's Jack Set
The machinist's jack includes lots of parts that you can mix and match to meet your needs.Machinist's jacks are used to support odd sized or odd shaped objects. Use them to support the ends of long workpieces that extend beyond your vise jaws. Use them to support the edges of items that you are clamping with your clamping kit.
|
End Mill Set Miniature, 10 pieces 2 & 4 Flute
|
1/2" Dovetail Cutter - 60 Degree
Dovetail Cutter
High speed steel cutter
|
Super Indexer
Functions as a rotary table or a super indexer. Mount it to your Smithy for single purpose or indirect indexing using the indexer's worm drive mechanism. Use the 6" chuck for a quick and easy way to mount small workpieces. Remove the chuck, attach the faceplate and its horizontal/vertical rotary table. 93 pounds. Additional shipping applies, $60.00 when bought with a machine and $75.00 when bought separately.
|
Chuck Flange for 6” & 8” Rotary table
Use this flange to mount the 33-104 5" three jaw chuck to the rotary table. *Note: You must provide/make your own mounting hardware.
|
5” Chuck for 6” & 8” Rotary Table
Turn your rotary table into a Super Indexer with this chuck. Align the chuck to the rotary table to easily mount your workpiece onto the rotary table. Great to use when machining multiple pieces. Can be used with either the 6" or 8" table. Rotary table chuck flange 33-103 required.
|
Indexable End Mill - R8
This indexable end mill has a 1.25" cutting diameter. It has an R8 shank and comes with one set of inserts.
|
Vise 3" Sine Screwless
3" Precision screwless sine vise. Jaw width is 3.15", jaw depth is 1.25", jaw opening is 4". The base size is 7.638" x 3.15". The center distance of the cylinders is 5.000". Hardened and precision ground to a tolerance of .0004" for both parallelism and squareness. Sine range: 0 - 60°. Jaw can be opened or closed without unbolting vise from work surface.
|
Replacement Clamp for V-Block Set
Misplaced a clamp for your v-block? Keep a spare or two just in case.
|
Dividing Head
Dividing Head
Cut gears and patterns quickly and easily with this ultimate cool tool. The 7” high head swings 6-1/2” and rotates up to 90 degrees or down to negative 10 degrees from horizontal. Features hardened and ground worm gear with 40:1 ratio, positive-locking mechanism with 360 degree brake shoe, and tapered roller bearings. Includes faceplate, tailstock, center and dog, threaded backplate, and three dividing plates.
|
R-8/MT3 Adapter Sleeve
If you have some MT3 Collets laying around, you can still use them with your Granite or stand alone mill. This adapter fits securely into an R-8 spindle and will accept MT3 tooling.
|
5C Spin Indexer
The 5C Spin Indexer is a quick, simple and accurate device for mill work. Mount your workpiece in the 5C Collet and thread it into the indexer. Great for miniature work such as clock gears. Comes complete with precision ground, 36-position index plate, calibrated in 1 degree increments. 5C collet not included.
|
5C COLLET HORIZONTAL/VERTICAL
5C COLLET HORIZONTAL/VERTICAL
|
Collet Block Set, Hex and Square
Holds standard 5C collets, Economical indexing for 2, 3, 4, and 6 divisions, Easy cross drilling at 60°, 90° and 120°, Made of hardened tool steel, Ground square and parallel within 0.0005" all over
|
R8 Spring Collet Set
Run spring collets in the millhead, tailstock, or headstock of your Midas series machine. Insert a spring collet and tighten with the safety wrench. Chuck holder head is 3” long and 2-1/2” in diameter. Set includes collet chuck with MT3 shank, 15 spring collets (1/8-1”), and a safety wrench. Requires 7/16” drawbar.
|
Collet set, ER20 12 pc 1/16" thru 1/2"
Collet, ER20
Use with a standard R8 3/4" collet for quick tool changes. Tool holders are designed to "bottom out" on the face of the R8 collet, giving you a fixed height each time.
|
Collet holder, ER20 3/4" shank
Collet Holder
Use with a standard R8 3/4" collet for quick tool changes. Tool holders are designed to "bottom out" on the face of the R8 collet, giving you a fixed height each time.
|
Adapter, end mill 3/16"
End Mill Adapter
Use with a standard R8 3/4" collet for quick tool changes. Tool holders are designed to "bottom out" on the face of the R8 collet, giving you a fixed height each time.
|
Arbor, drill chuck 3/4" x JT3
Arbor
Use with a standard R8 3/4" collet for quick tool changes. Tool holders are designed to "bottom out" on the face of the R8 collet, giving you a fixed height each time.
|
Roughing End Mill Set up 4
This 4 piece roughing end mill set lets you remove material quickly and effortlessly. Set includes 1/4”, 5/16”, 3/8” and 1/2” end mills with wooden stand.
|
KIT, 10 PC 2&4 FLUTE SIN END
KIT, 10 PC 2&4 FLUTE SIN END
|
7/16” Drawbar Kit ( Granite Series)
Pull collets and adapters up into your millhead spindle with these drawbars.
|
› Granite 3-in-1 Machine › Accessories
LR.jpg)
